نیکا نگر پارس
021-88781590
nika.smarthome@gmail.com
Instagram
  • صفحه اصلی
  • خانه هوشمند
    • آشنایی با خانه هوشمند
    • Z-Wave
    • امکانات خانه هوشمند
    • تجهیزات خانه هوشمند
    • brands
  • دوربینهای مدار بسته
    • آشنایی با دوربینهای مدار بسته
    • انتقال تصویر
  • دزدگیر
    • آشنایی با سیستمهای دزدگیر
    • تجهیزات دزدگیر
  • اعلام حریق
    • آشنایی با سیستم اعلام حریق
  • درباره ما
  • تماس با ما

FIBARO RGBW Controller

FIBARO RGBW Controller

FIBARO RGBW Controller
ساخته شده با برند FIBARO 
مشخصات عمومی
مشخصات فنی
قیمت و کد کالا
نحوه نصب
مشخصات عمومی

FIBARO RGBW Controller

The FIBARO RGBW Controller is a universal, Z-Wave compatible module that controls LED, RGB, RGBW strips, halogen lights and fans via 12 or 24 VDC. The device allows you to change the color of the lights from your mobile device whenever you want. Additionally, the controller supports up to four 0-10V passive analog sensors such as temperature sensors, humidity sensors, wind sensors, air quality sensors and light sensors. All IN and OUT terminals may be user-configured for LED control or 0V-10V signal readouts.

  • LED, RGB, RGBW LED, RGB,
    RGBW
  • Light controlLight control
  • Power meteringPower metering
  • Four output channelsFour output channels
Subpage of this product is under construction. Full presentation will be available soon.
مشخصات فنی
قیمت و کد کالا

 کد کالا : ۲۲۰

قیمت(تومان) : ۲۸۰،۰۰۰

وضعیت : —-

نحوه نصب

Installation

  • Turn of the electricity at the main circuit breaker
  • Removed the existing switch and disconnect the two wires (blue and brown)
  • Wire the Fibaro Dimmer module into the circuit using Figure 2 as a guide
  • Put the Dimmer module into position in the switch back-box, ensuring the cables are not damaged or kinked
  • Connect the wires from the dimmer’s Sx and S1 terminals to the light switch
  • Put the light switch in position and tighten the screws to the back box
  • Switch the power back on at the circuit breaker

Fibaro Dimmer 2 Connections

The Fibaro Dimmer has six terminals to connect it to the electrical wiring, this application note uses five of them:

Fibaro Dimmer Connections
  • L – Live
  • N – Neutral (this is connected to O in 2-wire installations)
  • O – Output – connected to light or load
  • Sx – power supply to switch (internally connected to L)
  • S2 – connection to Switch 2
  • S1 – connection to Switch 1

Fibaro Dimmer Parameter Setting:

The following parameters need to be set:

  • ۱۴ – ۰ – keep as default to work with momentary switch
  • ۱۴ – ۱ – enables the dimmer to work with a toggle switch (default is 0 for a momentary switch)

Earthing

All electrical circuits MUST be correctly Earthed.

All cables used in lighting circuits contain a bare Earth wire – this typically has a green/yellow sleeve when it is wired to the switch or backbox. The Earth is a very important part of the electrical system and all switches, appliances and lights must be correctly earthed.

For simplicity we do not show the earth wire in these drawings or explanations as it plays no active role in the day-to-day workings of your light circuits, it is there for your protection in case of emergency.

۸۸۷۸۱۵۹۰ (۲۱)۹۸+
۸۶۰۸۲۵۵۰ (۲۱)۹۸+
nika.smarthome@gmail.com
هرگونه کپی برداری از مطالب سایت با ذکر منبع مجاز میباشد