Our Smoke Sensor-Siren sets new safety standards in your home.
There are a lot of potential fire sources in your own four walls, for example open fire such as candles or a fireplace. Also an iron, cooking utensils or numerous other electrical device can cause fire. Smoke detectors can save lives! In case of a fire or smoke emission every second counts giving the chance to extinguish the fire or to get somebody or yourself out of harm’s way. The Z-Wave smoke detector detects resulting fire and smoke emission reliable. In case of emergency it alarms acoustically and sends alarm signal to Z-Wave network so that all other smoke detectors in range can be alarmed. That ensures that the alert reaches people in all floors as well as in the night while they are sleeping.
Beyond these functions the Z-Wave smoke detector can be used as an independent indoor siren which can be integrated into an existing security system. Within your Z-Wave smart home network the smoke detector can be connected to other sensors such as door and window contacts or motion sensors independently from a control center. In case of an alarm (e.g. burglary) the acoustic signal will be different from the signal in case of fire.
Smoke Sensor-Siren Description
This product combines a certified stand-alone smoke detector with an insertable Z-Wave module. The Smoke Sensor-Siren is certified by the VdS and DIN EN 14604 and satisfies all legal requirements. The smokebox is made of steel and antistatic plastic.
A button on the device can be used to test the smokebox, the electronics and the battery. In addition the device has an integrated test functionality to make manual tests with Aerosol unnecessary. The battery warning gets send for at least 30 days. During this time the smoke sensor stays fully functional.
A button on the Z-Wave module is designed to test the smokebox and sends the battery and smoke alarm to the Z-Wave controller. The smoke sensor can also be used as Z-Wave siren; for that the Z-Wave controller sends an on or off command to the siren. The radio module uses either the smoke sensors integrated 9V battery or can be powered by an external 12V power supply.
According to the VdS 3515 (smoke sensors with radio communication) this device will relay all alarms to all other smoke sensors (004001) in the Z-Wave network to create a house-wide alarm. This connection of theSmoke Sensor-Siren is fully automatical and needs no further configuration. The Smoke Sensor-Siren and the controller communicate via an secure protocol to prevent manipulation.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
press the button on the bottom of the device for at least 10 seconds
Safety Warning for Batteries
The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.
|IP Class||IP 20|
|Battery Type||۱ * ۹V Block|
|Z-Wave Product Id||0x0154.0x0100.0x0201|
قیمت و کد کالا
کد کالا : ۴۰۴
قیمت(تومان) : ۴۲۵،۰۰۰
وضعیت : موجود
Please refer to the installation guide of the smoke sensor for information about how and where the smoke sensor should be installed. The installation guide complies with the norm DIN EN 14676.
- Remove the bracket from the detector main unit by rotating it counter-clockwise.
- Place the bracket where you are going to install the detector. In each of keyhole slots, draw a mark to locate plastic anchor and screw. Using a 3/16-inch (5mm) drill bit, drills two holes at the marks and insert plastic anchor, and attached the bracket by using the screws.
- Open the battery compartment (1) to activate the battery, and then close the cover.
- The optional external power supply will connect to the connector (5). The internal battery must stay inside the detector even when the external power supply is connected.
- Mount the smoke detector to the mounting ring. Make sure the hooks of the detector are placed between the hook and the twist stopper (2) of the mounting base (arrows in image above). Then turn about 15 % clockwise. (Hint. If the detector hook is not placed right between the two mounting ring structures the detector can?t be mounted to the ring).
Please follow the recommendations about amount as position of the sensor in your home as given above. Avoid to place the sensor into the angle of walls, prefer positions in the middle of the room.